五十铃 240HP FVR 油轮消防车

Outer dimensions

8140×2550×3470mm

Maximum total mass

17000kg

Fluid carrying capacity

The water load is 4650kg, and the foam load is 1950kg

Top speed

95km/h

Fire pump rated flow

60L/s@1.0MPa;

Rated flow rate of fire cannons

48L/s 1.0MPa

Fire cannon range

Water≥70m Foam≥60m

Specific power

177/17=10.41

Approach/Departure Angle

20°/10°

Model

QL1180XMFRY

manufacturer

ISUZU Technology

Engine model

Japanese ISUZU technology diesel engine6HK1-TCL

Engine power rating

177kw

Engine displacement

7790ml

Engine emission standards

GB17691-2018 China V.

Drive form

4×2

wheelbase

4500mm

Maximum allowable gross weight

18000kg

Minimum turning radius

≤19m

Gearbox

Manual

Power take-offs

Sandwich power take-off

structure

Flat-headed, four-door, restructured double-row cab

Number of drivers and passengers

2+4 seats with CBA type

Driver's position

Left side

equipment

The original vehicle dashboard is equipped with a fire operation dashboard and a warning light control box, which is installed

1、Siren;

2、power take-off control switch and indicator light;

3、additional power switches;

General arrangement

The vehicle is composed of two major parts of the firefighter cabin and the body, and the body layout adopts a three-point structure, the front part is the equipment box, the middle part is the water tank, the rear part is the pump room, and the tank body is the parallelepiped box type tank.

structure

The main frame structure is welded with high-quality square tubes, the outer decorative plate is welded with carbon steel plates, the roof is non-slip and walkable, and the lower part of the equipment box on both sides is provided with flip pedals and aluminum alloy anti-skid plates.

Equipment box

The equipment box is located at the rear of the crew compartment and has aluminum roller shutters on both sides with lights. Storage boxes are set up in the equipment box according to needs. There are tool boxes and roller shutters on the side lower skirts for small tools

Pumping station

The pump room is located at the rear of the vehicle, with aluminum alloy shutter doors on both sides and behind, with lights inside, and some commonly used equipment can be placed on both sides of the pump room

Holding position: Install fuel heater (optional according to customer needs).

Climb the ladder and get on the car

The rear ladder is made of aluminum alloy two-section flip ladder, which is used and does not exceed 350mm above the ground when used.

Capacity

5000kg

Material

High-quality304 stainless steelwith a thickness of 5mm

The tank is fixed

Elastic connection with chassis frame

Tank settings

Manhole: 1 DN470 manhole, with quick locking/opening device

Overflow port: 1 DN65 overflow port

Residual water outlet: Set up 1 DN40 water tank residual water outlet, equipped with ball valve

Water inlet: connect one DN65 interface on the left and right sides of the tank

Water inlet and outlet: 1 water tank to pump inlet pipe, DN150 valve, pneumatic and manual control, 1 water pump to water tank filling pipe, DN65 valve, pneumatic and manual control

capacity

1000kg

Material

304 stainless steelwith a thickness of 5mm

The tank is fixed

Elastic connection with chassis frame

Tank settings

Manhole: 1 DN470 manhole, with quick locking/opening device

Overflow port: 1 DN65 overflow port

Residual water outlet: Set up 1 DN40 water tank residual water outlet, equipped with ball valve

Water inlet: connect one DN65 interface on the left and right sides of the tank

Water inlet and outlet: 1 water tank to pump inlet pipe, DN150 valve, pneumatic and manual control, 1 water pump to water tank filling pipe, DN65 valve, pneumatic and manual control

Model

CB10/60 fire pump for atmospheric vehicles

Form

Low-pressure centrifugal type

Rated flow rate

60L/s @1.0MPa

Outlet pressure rating

1.0MPa

Maximum suction depth

7m

Water diversion device

Comes with a sliding vane pump

Diversion time

The maximum suction depth≤50s

Pipe Material

High-quality seamless steel pipes

Suction lines

There is a DN150 suction port at the rear of the pump room

Water injection lines

A DN65 water injection port is set on the left and right sides of the water tank, and a DN65 water pump is provided in the pump room to inject water into the tank

Outlet lines

There is one DN65 atmospheric water outlet on the left and right sides of the pump room, with a shut-off valve and a cover

Cooling water lines

Cooling water line and control valve with cooling power take-off

Model

PH48

Material

The housing is cast aluminium and the overflow section is stainless steel

form

Negative pressure ring pump type with flushing device

Mixing ratio

3-6%

模型

PL8/48泡沫、水两用炮

制造商

成都威斯特消防设备有限公司

额定流量

48升/秒

额定压力

0.8兆帕

海拔

≥70°

俯角

≤-30°

范围 （米）。

水≥70米泡沫≥60分钟

水平旋转角度

≥360°

驾驶室内控制装置

泵脱机、报警灯报警、照明及信号装置控制等

泵室内控制

上装主电源开关、参数显示、状态显示

附加电气

设置独立电路

辅助照明

消防员室、泵房、设备箱分别设有照明，控制盘设有照明及指示灯

频闪灯

车身两侧安装有红、蓝频闪灯

警告装置

驾驶室顶部安装着一排长长的全红色警灯

警报器，其控制箱位于驾驶员前方下方

火场照明

车体后部安装有1盏35W消防探照灯

面漆

高品质国产漆器

颜色

车外表面主色为RO3消防红，可选蓝色、黄色、灰色等

1

根据灭火实际需要，按照消防操作规程，就近取放。

2

采用防锈、防震、防脱落、防刮的专用夹具固定。

3

标识醒目，多人操作，互不干扰。